beamticket26

Fiat 500 Replacement Key Fob If your remote key fob has stopped working, it's time to replace the battery. If you do replace the battery but it doesn't work it is probably elsewhere. United Locksmith specializes in the creation of new keys for classic automobiles. We have all the tools and components needed to provide this service. Dead Coin Battery The most frequent reason that your Fiat 500 key fob will not lock or unlock the doors is due to a dead battery. The key fob has the battery of a coin-cell that will drain quickly when it isn't frequented enough. If your remote has started to show signs like a loss in range or stopped working or not responding, then the battery could be dead. Metal clips hold the battery in within the key fob. If the clips are loose, it can cause problems with contact, which can prevent the remote from receiving power. Make use of a flathead screwdriver to open the retaining clips and remove the battery. Make sure you use an identical replacement battery type of voltage, size and specifications as the original battery. The exposure to water can cause the key fob to corrode or become damaged. Even simply click for source in soapy, warm water can cause damage to the chip. It's best to keep your key fob in a dry location. Water Damage If your key fob isn't working correctly, it could be due to water damage. Key fobs are fitted with rubber seals that stop them from being damaged by rain or splashes of water. However, it is crucial to keep your keys away from the pool, ocean and the washing machine! The key fob comes with an electronic chip inside that transmits a signal car's immobilizer system. This is the reason why your 500 can lock or start, but should the chip become wet, it's unable to longer work. You can try cleaning your key fob's internal electronics with isopropyl alcohol or an electronic cleaner to see if they are still good. It is recommended to replace the key fob when it's submerged into salt water rather than attempting to repair it yourself. Although a replacement fob may cost a little money, it is a lot cheaper than paying for your Fiat 500 to be towed to a dealership and fixed! In addition, you can do it yourself with only a few steps. Be sure to have the correct battery type prior to opening your keyfob. This task is more straightforward than it appears and you can find step-by-step instructions on the internet for nearly any car key fob. Faulty Chip The chip in the key fob communicates directly with the immobiliser of your car to ensure that your vehicle will only start when right keys are in place. If the chip is damaged or corrupted the car won't start, no matter what you do. A faulty chip can occur due to a variety of reasons but most often it is due to water damage or a dead battery. It is best to hand over the task to a professional locksmith who will be able to replace the chip in a short time and at a an affordable cost. If your key fob will not function after exposure to clean water from a tap or rain take the battery off. Clean the electronic component with a towel. If the key fob still doesn't work, it is likely a fried chip and will need to be replaced. Some people will go to their dealer when in need of a new Fiat key fob, however this is a costly option. If you're looking for a low-cost solution to get your Fiat key fob repaired Look no further than United Locksmith. We have all the tools and knowledge required to fix your Fiat fob in a timely and professional way. Faulty Receiver Module Fiat key fobs transmit an alert up to 50 feet to the vehicle, which can unlock and close the doors (and start the vehicle if it has automatic transmissions). There are several reasons why the fob may stop working. This can be caused by a dead coin-battery water damage, worn out buttons an issue with the receiver, signal interference or an issue with the chip. If the fob was stored in a place that has experienced extreme trauma, such as being dropped on hard floor or getting washed in a washer the fob may not be able to communicate with the car's Body Control Module (BCM). This is because the BCM is an extremely secure system that will only accept signals from a genuine original key and not another. If this is the case, then you will need to replace your fob. A locksmith professional can handle every aspect of the replacement process and even program a new one for your 500. In fact, they'll offer you a clone key that functions exactly like the original fob (and costs less than the cost).